Fraises CraftPro

Single Flute Straights

Single fluted Tungsten Carbide straight cutter for fast free cutting.

• Single flutes should be chosen where speed and clearance rates are more important than the finish.
• Depth of cut should not exceed cutter diameter.

Two Flute Straight

Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising.

• Use on softwoods, hardwoods, MDF, plywood and chipboard.
• All cutters have a bottom cut feature.

For grooves and trenches

Template thickness should be 5mm thicker than cut length of cutter.

• Can be used to rout both tenons and housings.

Hinge recess

Two flute TC cutter giving good chip clearance.

• Ideal for shallow lateral routing cuts such as recessing hinges.
• Corners will require final trimming square with a hand chisel or a corner chisel.

Pocket Cutters

A two flute cutters with extra long shanks.

• Deep grooving, rebating and mortising.
• Useful for template work when thickness of template restricts depth.
• Extra care must be taken to avoid breakage.
• Take more passes than usual, and only cut up to half the diameter of the cutter in one pass.
• This applies to cutters under 3/8 inch diameter.

Self Guided Bevel Trimmers

This is bearing guided and gives a smooth bevel finish for laminates and other materials.

• Bearing follows the board beneath.

Self Guided Trimmers

Used for trimming plastic or plywood overlays.

• Also for copy profiling with a template.

Strip recessers

Recessing cutter for producing double rebates.

• For producing recesses with a lower rebate.
• Designed to accept library/bookcase strip. Ref. C231 is specifically designed for Tonk Strip.

Template/Profilers

Shank mounted bearing profilers are ideal for template guidance.

• Use for rebating and trimming edges only.
• Extra care must be taken to avoid cutter breakage.

45 Degree Pin Guided Chamfer Cutter

Ideal for fast chamfering.

• Popular in the sign making trades.
• For chamfering edges of plastic material .

Bearing Guided Bevel

Ideal for posts and newel caps for stairs.

Chamfer 'V' Groove

For veining, panelling, 'V' grooving, bevelling & chamfering.

Chamfer 'V' Groove Shank Mounted Bearing

For veining, panelling, 'V' grooving, bevelling & chamfering.

Shank Mounted Bearing Chamfer

For veining, panelling, 'V' grooving, bevelling & chamfering.

Triple Flute Solid Carbide Engraver

Cuts cleanly without feather edging.

• Solid Carbide for long life.
• Cuts to a fine' V' groove point.
• Ideal for sign writing.

For use with a router

These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a template and guide bush fitted to the router base should be used.

Right Hand Rotation

Purpose made for stair housing jigs.

• Ensures tight fit of tread in string.

Bearing Guided Round Over & Ovolo

Self-guiding cutters for rounding over edges do not require a side fence.

• They are supplied with two bearings.
• Use the larger bearing for a round-over.
• If the cutter is lowered, a top quirk can be produced.
• Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece.

Radius Cutters

These are ideal for engraving and decorative panel work.

• Made with Solid Tungsten Carbide inserts, with two flutes.

Self-Guided Radius Cutters

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with.

• The guide bearing follows the vertical edge or template. Alternative bearing Ref. B127A creates a shallow radius.

Bearing Guided Tradional Torus

Classic skirting board mould.

Staff Bead Cutter

These staff bead are ideal for producing nosings and attractive edges. Edge cut only. Ref. C068 can be used with Ref. C181 for dust proof joints.