Professional TCT Cutters

Diameters from 2.0mm to 12.7mm

• TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
• Two flutes give a clean finish to cut edges.
• All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
• Stock available: 5

Eccentric single flute

• Eccentric single flute cutters.
• Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.
• Cutters with prefix S are Solid Carbide.
• Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass.
• Small diameter tools must be handled with care to avoid breakage.
• Single flute cutters should not be used in eccentric chucks.
• Stock available: 2

Pin guided rebaters to follow work edges

• The guide pin follows the work edge to give a preset width of rebate.
• Ref. 8D/4 can be used to create a counterbore for a slot to accept M5 and M6 pan head screws.
• Stock available: 4

Bearing Guide 90 degree

• Blades of cutters Refs. 46/01 & 46/03 can be rotated through 180 degrees to give one new cutting edge.
• Blades for 46/010 can be rotated by exchanging blades over.
• Refs 46/02 have blades that can be rotated in 90 degree increments giving three extra new edges.
• Stock available: 3

Bearing mounted on end of cutter

• Self-guiding trimmers with bearings mounted on end of cutter.
• For trimming plastic or plywood overlay.
• For copy profiling, use the bearing to follow a template or base edge of board.
• An approximate 3mm overlap should be left before copy profiling. When using plastic laminate adhesive to dry before trimming. This avoids clogging the guide bearing.
• Refs. T46/1, 46/2 and 46/20 are downcut to prevent breakout on veneer.
• Ref. 46/211 has a sleeved bearing to allow for regrinds in case of resharpening.
• Stock available: 2

Combi trimmer

• For trimming top & lip.
• Economical cutters, perform 3 functions:
• 1. To top trim the overlay at 90 degrees.
• 2. To trim the overlay at 45 degrees or 60 degrees.
• 3. The base of the cutter can trim the vertical lipping at 90 degrees.
• Requires side fence or roller bearing.
• Stock available: 4

Two flute flush trimmers

• For trimming the lipping of plastic overlay, and for rebating and
• machining wood, Duralium and plastics.
• Tungsten Carbide Tipped.
• Use at speed 12000 - 24000 RPM.
• Stock available: 10

For frame construction

• This cutter simplifies the construction of framing.
• The scriber matches the profile to form a shoulder scribe.
• Tenon and groove/rebate must be cut separately.
• Stock available: 5

Mortar Groove & Large Chamfer

• Use for producing mortar grooves and for bevelling applications.
• Stock available: 4

Pin Guided Chamfer

• Ideal for fast chamfering.
• Popular in the sign making trades.
• For chamfering edges of plastic material .
• Stock available: 8

For dovetails joints and sliding dovetails.

• For dovetail joints and sliding dovetails.
• To suit user preference, the table shows angles from the horizontal and the profiles show angles from the vertical.
• Stock available: 1

• For use with commercial dovetailing and stair-housing jigs.
• The cutter will produce sliding and lapped dovetails, through dovetails and end on dovetails.
• Right hand rotation.
• Purpose made for stair trenching machines.
• Stock available: 8

Without Bearings

• Some Ovolo cutters can be used with radius cutters, to make rule joints.
• Ref. 7/01 has an extra long shank of 40mm.
• Stock available: 7

Pin Guided Ovolo Cutters

• Small solid guide pin can follow more intricate shapes in contrast to bearing guided cutters.
• Stock available: 14

Pin Guided Round Over Cutters

• Small solid guide pin can follow more intricate shapes in contrast to bearing guided cutters.
• Stock available: 5

Sash bar and rule joint

• Can be used to make rule joints or glazing bar joints.
• Stock available: 7

Sash Bar Ovolo Joint

• Designed for sash bar window construction.
• Stock available: 15

Staff Bead & Nosing

• Beads Refs. 9/10 & 9/11 have matching cutters Refs. 8/10 & 8/11 for jointing & hinging.
• Stock available: 2

Staff Bead/Jointers

• A long glue line gives extra strength. Can be used in conjuction with Refs. 9/10 & 9/11. Ideal for dus proof hinged joints in display stand.
• Stock available: 10

With guide pin

• Pin guided cutters permit freehand edging at considerable speed.
• Ideal for cutting small intricate shapes.
• Stock available: 13

Cavetto/Panel Mould

• These edge moulds can also be used to create panelling effects, when using the whole width of the cutter.
• Stock available: 7

With Guide Pin

• Self guiding for freehand edging.
• Stock available: 13

Without bearings

• Classic ovolo cutter.
• Use with a side fence.
• Stock available: 5

Classic Set

• The classic method of producing cabinet panelled door and drawer fronts is made easy with the Profile Scriber set.
• The components are rearranged on the arbor to cut the profile or the scribe.
• Stock available: 1