Varijig Clamp Guide Accessories

Varijig clamp guide router base plate

Plunge router base base accessory for the Varijig clamp guides.

• Base plate engages in the T-slot in the extrusion.
• Made from clear plastic.
• Includes adjustable guide bar for perfect tracking using hex key provided.
• Fits all Varijig clamp guides.
• Clear plastic allows for good visibility.
• User must drill plate to fix router.
• Varijig clamp guide and router not included.

Varijig clamp guide adjustable guide stop

Varijig clamp guide adjustable guide stop.

• A short alloy extrusion rail that can be fixed anywhere along the length of the Varijig clamp guide.
• The removable alloy adjustable bridge guide stop can be locked in place so that it limits the rail travel in a set position from an edge.
• When the bridge guide stop is removed the short rail can be used for stopped housing and grooves that need to stop short of an edge.
• Double locking knobs for security.
• Ideal for repetitive grooves.
• Will also fit Varijig Frame System extrusion.
• Varijig clamp guide not included.

Varijig clamp guide back to back clips

Varijig clamp guide back to back clips.

• Clips comprise of alloy brackets and knobs.
• Allows two Varijig clamp guides to be joined back to back.
• Clamp one clamp guide to the bench and use the clips to attach another clamp guide upside down.
• Raises component up 32mm for unobtrusive clamping for full edge moulding.
• Back to back facility allows clamping of large panels and work pieces.
• Back to back clips require two Varijig Clamp Guides to be used.
• Depending on length of guide used, either four or six clips are needed.
• Wide components will require additional support to prevent tilt or the use of a second pair of clamp guides and clips.
• Varijig clamp guides not included.

Varijig clamp guide end stop block

Varijig clamp guide adjustable end stop block.

• Engages in the T slot on the clamp guide extrusion and can be locked in position using locking knob.
• Can be used with all Varijig frame system extrusions.
• Varijig clamp guide not included.

Varijig clamp guide feather board

Feather board finger pressure accessory for Varijig clamp guides.

• Clamps to the Varijig clamp guide which can then be clamped to a router table top.
• Provides horizontal side pressure for safer table routing.
• Varijig clamp guide not included.
• Guard removed for clarity.

Varijig clamp guide handle lever extension

Lever extension handle for Varijig clamp guides.

• Gives better leverage to operate the clamp, especially when more clamping pressure is required.
• Slides onto Varijig clamp guide lever.
• Increases lever length by 134mm.
• Varijig clamp guide not included.

Varijig clamp guide jaw kit

Pair of plastic jaws that are screwed onto the jaws of the Varijig clamp guides.

• Distributes clamping pressure over the workpiece to minimise clamping marks.
• Allows Varijig clamp guide to be squared up to the wood edge.
• Built in mounting holes allow a batten to be fitted to increase jaw width further.
• Varijig clamp guide not included.

Varijig clamp guide saw base plate

Circular saw base base accessory for the Varijig clamp guides.

• Base plate engages in the T-slot in the extrusion.
• Made from plastic.
• Includes adjustable guide bar for perfect tracking using hex key provided.
• Includes adjustable guide bar for perfect tracking.
• Fits all Varijig clamp guides.
• User must drill plate to fix circular saw.
• Varijig clamp guide and saw not included.

Varijig clamp guide side to side clips

Varijig clamp guide side to side clips.

• Clips comprise of alloy brackets, t-nuts and knobs.
• Allows two clamp guides to be joined side to side.
• Clamp one clamp guide to the bench and use the clips to attach another clamp guide next to it upside down.
• Side to slide clips require two Varijig Clamp Guides to be used.
• Side to side facility allow obstruction free working.
• Six adaptors are included in the pack so that three pairs of clamps can be linked securely together.
• Low profile clamping.
• Ideal for sanding.
• At least two clips must be used for side to side work.
• Two clamps joined creates a 112mm wide component support surface.
• Wide components will require additional support to prevent tilt or the use of a second pair of clamp guides.
• Varijig clamp guides not included.

Varijig clamp guide squaring attachment

Allows Varijig clamp guide to be squared up more accurately.

• Large 90 degree head allows the Varijig clamp guide to be used as a clamping T- square.
• Serrated front edge for grip.
• It is secured to fixed jaw using two self tapping screws.
• Varijig clamp guide not included.