DEALER LOGIN
Trend
Login  |  Register
Items 0  |   View order

Plant Pot Holder Routing Project

Plant Pot Holder Routing Project
  A modern upright style planter with panelled sides.

One of the hazards of being a professional woodworker is that you are continually at the mercy of friends and family who don’t appreciate how much time, effort and materials are involved in even the simplest of jobs. I have come to dread the phrase “but it would be dead easy for you to knock one up”, as roughly translated this really means ‘make it for us on the cheap’!

No one ever considers the material cost, that is assumed to be carried by someone else’s job; and yes, it might only take you a few hours to ‘knock up’, but it has taken you 25 years of hard graft to learn how to do it this quickly, as well as a considerable tool and machinery investment, probably amounting to several thousand pounds. But sometimes it is hard to say no and the request for this modern style planter was one of those jobs that just might lead to more work, (but in most cases doesn’t), so once again I had to smile sweetly and say “no problem”.
     
Material Choice
  1. The only answer was to use scrap timber to keep material costs down to a minimum. This is always a good chance to use up some of those short off-cuts that seem to accumulate under the bench, and which you keep saving for a job ‘one day’. I managed to find a selection of leftover bits of softwood and two old shelves, which although superficially very tatty would be magically transformed after a few minutes work with the band saw and planer.
Material Choice
  2. With a decent quality 6 tpi blade in the band saw, you can quickly slice up all the odd sized pieces into the standard dimensions you require for the project.
Material Choice
  3. Cut out quite a little more than you theoretically need, as a few spare pieces are really handy for trial cuts when setting the machines to the critical dimensions required for joint making and panel raising later.
Material Choice
  4. Also, particularly with softwood, there are often a lot of large dead knots which will seriously weaken the timber and you need enough spare material to be able to work round these, You will never be able to cut out all the knots but try to work round the largest of them.
     

Cutting

Cutting
  5. For accurate joint making it is vital that the timber is prepared true, so spend a little time making sure that the fence on the planer is set perfectly square.
Cutting
  6. Just because it was right last time you used it doesn´t necessarily mean that it is square now, so do check it occasionally. Once you have prepared the face side and edge on each piece pass it through the thicknesser to get it all fully dimensioned.
Cutting
  7. Do check the grain direction on each piece before you pass it through the thicknesser to minimise the amount of finishing work you have to do later.

Use a chop saw with a fine tooth blade to cut everything to length, cutting out as many knots as possible, Because you are working with off-cut material, which is by definition is usually short in length, there is inevitably a lot more waste, but as the original material was effectively free anyway this doesn´t really matter
Cutting
  8. The best way to ensure consistency of size for matching components is to cut them all together. You don’t stand a chance of getting the joints to fit probably if the components vary in length, even by a very small amount.
Cutting
  9. Lay out each frame to check the overall dimensions. Notice that the uprights for two of the frames are reduced in width, so that when they are joined together at right angles the finished dimensions on each frame will match.
     

Table Routing

Table Routing
  10. The central panel is set into a groove in the frame and the same groove also forms the joint for the frame. One of the best ways of grooving is using a dedicated grooving cutter mounted on an arbor in the router and although the width of a groove is fixed you can vary the depth by altering the diameter of the bearing.
Table Routing
  11. Although this arrangement can be used freehand it is much more convenient to use it with a router table, but select a table insert that will provide maximum support but remain clear of the cutter.
Table Routing
  12. Bring the router table fences in as close as possible to the cutter, again to provide maximum support and make sure they are locked up tight. Use a straight edge to level them through with the bearing on the cutter.
Table Routing
  13. For safety, set up some form of hold-down mechanism to keep the work pressed against both the table and the fence. I find a simple featherboard arrangement is often the most effective way.
Table Routing
  14. This business of holding firm against the fence is particularly important with the narrower frame components which are prone to chattering unless they are supported properly.
     

Table Routing Continued

Table Routing Continued
  15. The panels themselves are cut from the old shelves and run through the thicknesser to clean up any surface marks. It is amazing what lies within even the scruffiest of looking pieces.
Table Routing Continued
  16. The raised profile of the panel can be created in several ways, but once again the router provides the most efficient method. Having said this though, the dedicated cutters are initially quite expensive but if you use them carefully and look after them, they should last for years. There is quite a range of profiles available but I settled on a plain angled shape, more in keeping with the contemporary look I was trying to achieve with the planter.
Table Routing Continued
  17. It is very important with these large diameter cutters that you check carefully on the packaging for the maximum recommended speed and make sure your router is set to this before you start. Working at a high rpm risks damaging the cutter, the router, the work or yourself, so take care.
Table Routing Continued
  18. Big cutters should never be used freehand, only ever in the router table but do check to make sure there is enough clearance in the table aperture, If not, you can often still use the cutters, by making up a false tabletop from MDF and cutting a larger aperture in this.
Table Routing Continued
  19. Start profiling the panel making the end grain cuts first, It is not good practice to try and achieve the finished profile in one pass, take several to reach the required depth.
     

More with the Router and Table

More with the Router and Table
  20. The end grain cuts usually result in some breakout.
More with the Router and Table
  21. This is all removed by the cut down the length of the grain.
More with the Router and Table
  22. Repeat the procedure several times progressively increasing the depth of cut until the flat section is a nice sliding fit in the frame grooves, If you find that the cutter is burning, particularly on the end grain, try reducing the speed of rotation and/or hone it lightly with a Diamond file to restore a sharp cutting edge.
More with the Router and Table
  23. When you are forming the groove in the cross rail components of the frames remember to groove across the end as well, as this is used to form the joint, I actually forgot and had to reset the grooving cutter, another half hour wasted for a moments inattention!
More with the Router and Table
  24. Try a dry assembly of the panel to make sure the frame will pull together without any gaps.
     

Glueing and Biscuit Jointing

Glueing and Biscuit Jointing
  25. If it is all okay, apply some glue to the end of each cross rail and clamp it all up around the panel. Do not apply any glue to the panel itself as it needs to be free to move with changing weather conditions once the planter is exposed to the elements. Any attempt to fix the panel permanently in place will almost certainly result in it subsequently cracking. Cut some small tongues to fit into the grooves to complete the joint and tap these in place.
Glueing and Biscuit Jointing
  26. If you use the foaming polyurethane type of glue this provides a completely weatherproof bond and also expands to fill in any small gaps.
Glueing and Biscuit Jointing
  27. It dries in about half an hour but if you leave it several hours the excess foaming can be cut away cleanly with a sharp chisel and there are none of the staining problems normally encountered if you use PVA.

The four completed panels are biscuit jointed together to form the planter box, I used three biscuits per side to maintain the alignment.
Glueing and Biscuit Jointing
  28. For the final assembly you will need plenty of clamps, but keep checking that the box is remaining square, it is so easy to pull it out of alignment with a carelessly applied clamp.
Glueing and Biscuit Jointing
  29. Corner braces are glued into the bottom of the planter which as well as adding strength also provide a seating for the loose base.
     

Assembly

Assembly
  30. To prevent the base from rotting it is best to raise it slightly off the ground on some small feet and for this purpose I used some small squares of oak which is far more weather resistant.
Assembly
  31. These are simply glued in place and then routed with a tiny radius to form a neat but unobtrusive foot.
Assembly
  32. The four corners of the planter box are chamfered with the router, finishing the chamfer in line with the cross rails..
Assembly
  33. The top of a planter is covered with an overhanging frame made from the same sized material as that used for the panel framework .
Assembly
  34. The corners are biscuited together and the whole assembly is just glued in place, using weights to hold it in position while the glue cures .
     

Finishing Touches and Presentation

Finishing Touches and Presentation
  35. Once everything is set any excess glue can be cleaned off with a sharp chisel and the planter can be sanded thoroughly ready for finishing.
Finishing Touches and Presentation
  36. The actual finish is a matter of choice as there are dozens of different decorative clear and coloured finishes available specifically for outdoor use. To maintain the contemporary feel I used a silver coloured waterproof stain, applying two coats with a brush.
     
< Back to Index Previous   Previous   |  Next   Next
https://uk.trustpilot.com/review/trend-uk.com [^]
 
  Aspin Interactive e-commerce